Ultra-strong flakes are hot-blended for guaranteed consistency from sulfur, mineral filler, and special components to give top performance, even for high-strength concrete tests.
Sulfur compound melts quickly at 240-260°F, pours at about 275°F, and hardens in minutes with minimal shrinkage. Compressive strength exceeds 8000 psi at 2 hr. for 2" cube test of ASTM C 617, and may be used beyond 15,000 psi as a bonded cap with added aging.
Compound Melting Pot
Melting pots are useful for preparing capping compounds, wax, tars, asphalt, and other materials in the lab. Each has precision temperature control for 38-160°C (100-320°F) range that holds to set point. A high limit control turns pots off at 182°C (360°F). The cast aluminum inner liner is contacted from top to bottom by a unique helically wound element to give even heat distribution. Durable polished stainless steel outer case assures long, dependable service.
Stainless steel ladle with 4" dia. bowl for transferring capping compound from melting pot to capping fixture.
CP-006 Vertical Capper-6" Diameter
For capping 6" x 12" concrete test cylinders for compression tests. Assures plane end surfaces at right angles to cylinder axis. Includes positioning guide. Use with all types of capping compounds. Plate finish-ground from cold-rolled steel to .002" planeness.
CP-004 Vertical Capper-4" Diameter
For capping 4" x 8" concrete test cylinders for compression tests. Assures plane end surfaces at right angles to cylinder axis. Includes positioning guide. Use with all types of capping compounds. Plate finish-ground from cold-rolled steel to .002" planeness.
Universal Vertical Capper
Universal Vertical Capper for 4", 3" & 2". Base and capping plate are machined from cold-rolled steel. Capping plate is finish-ground within .002" (.05mm) planeness. Guide is machined from high-strength, cast-aluminum alloy. Change out plate for different size samples.
Universal Capper w/ 4" Plate (H-2925C) 3" Plate Only (H-2925B.1) 2" Plate Only (H-2925A.1)
The Neoprene Compression Pad, made of tough elastomeric material, flows into irregularities and distributes the test load uniformly without creating air pockets to assure consistent breaks.
Compression pads are available in several hardnesses:
50 durometer 1500 to 6000 psi max 100 reuses 60 durometer 2500 to 7000 psi max 100 reuses 70 durometer 4000 to 7000 psi max 100 reuses 70 durometer 7000 to 12,000 psi max 50 reuses & qualification testing MEET ASTM C1231
ACM-24 Compressive Pads for 2" x 2" Cubes 4/set
Pads are used to cap 2" x 2" cubes. Four pads per set. Two red for normal strength and two amber for higher strength. You can also specify all of one color if you want. Square Retainers also available to be used with the compressive pads.
Steel Curing Tanks
H-2961 2' x 2' x 4' H-2961.1 2' x 2' x6' H-2961.2 3' x 2' x 8' H-2961.3 3' x 2' x 10'
Useful for curing cylinders, beams and material needing total immersion in laboratory or the field. Tanks are constructed from 20GA. galvanized steel; side walls are deeply corrugated and made from one piece, having only one side seam. All joints are assembled with elastic packing and rivets. Rolled into the metal at top of the tank is a steel pipe, forming a rigid top that will not break or get out of shape. Larger tanks are supplied with top angle brace. Meets ASTM C192; AASHTO T127.
TH-100 Curing Tank Heater
The Curing Tank Heater is an economical unit used to control water temperature in concrete curing tanks. Unit includes two thermostats; one adjustable between 35° and 95°F; the second maintains element at safe operating temperature. It has a 1000 Watt heating element (115/60/1).
TP-Pump Curing Tank Circulating Pump
This versatile circulating pump can be used submerged or in open air. Using magnetic drive it has no shaft seals to wear, leak, replace or reduce power. Pump is 1/200 HP, 19 watts, 0.45 amp. Inlet is a screen and outlet is 0.25"MPT. A maximum pressure of 50psi can be obtained.Normal voltage is 115V, 50/60 Hz. A 6ft. cord is supplied. Dimensions 4 x 3.25 x 3.75"LWD.
SC-15 Sample Cart
Designed for handling lab samples, cart moves up to 400 lb with ease. Cart is painted steel with two shelves 30x16x3.5" deep. Large 5" diam. wheels are fixed at rear, swivel on front for ease of handling. Overall dimensions: 34x17x31.5" H . Unassembled.
ST-1 Cylinder Stripping Tool-Screw Driver Handle
Stripping tool allows quicker, easier stripping of concrete test cylinders. Made of hardened steel with strong, molded plastic handle.
ST-2 Cylinder Stripping Tool-T Handle Type
T-Handle-style mold stripper, splits single-use cylinder molds for cylinder removal.
CR-87B Chart Recording Thermometer
Advanced microcontroller design
Large led digital temperature display
3 temperature ranges and 4 chart speeds
Front panel selectable single turn or continuous chart rotation
All controls are located on the front panel for fast and easy setup
Furnished complete with 2 cartridge pens and 60, 6" diameter assorted charts
Standard 120 volt operation
Battery back-up. Assures normal operation during power interruptions
12 volt operation. Allows use in vehicular or marine operations
Freestanding or wall mounted (using existing keyhole slots located on back of case)
Durable polycarbonate Case, cover, and handle
MRCS Moisture Room Control System
The heart of every of every system is the control panel. This control panel automatically blends hot and cold water to the desired temperature for your curing environment. (73.4 ± 3°F)
H-2734 Fogging Fan
Designed specifically for small spaces that need a dependable unit in environments up to 100% RH (relative humidity). Well suited for areas between 16 to 30 feet in length, (and can be used in smaller areas down to 12 foot) this model has a maximum fogging output of 5 GPH and can propel fog up to 20 feet. The H-2734 utilizes a two-blade fan, making it about 30% quieter than larger units. The nozzle-free fans can atomize ordinary water supplies into a very fine mist-like fog. Utilizing high-speed centrifugal force and powerful air flow, these units can propel a misty-fog stream up to 20 feet away.
The powerful H-2734 is engineered to withstand humid conditions as high as 100% RH and above, and corrosive environments containing salts, lime, ammonia and other acidic compounds. Units are constructed of impenetrable components like Nema 4 connections, all 304 SST hardware, UV stabilized polyethylene plastics, PVC dip-coated steel, and sulfuric anodized aluminum. Standard configuration includes a Baldor wash-down-duty motor that is specifically designed for wet, corrosive environments, 115/230V, 1ph, 60Hz.
Included with unit is an: adjustable-angle hanging bracket; visual flowmeter panel with strainer, 12 ft. SJO indoor/outdoor, heavy-duty power cord; 20 ft. Poly-Flo water line tubing; 16 ft. water drainage line; 100% stainless steel hardware, and easy-to-follow operator’s manual.
P54-100-312 Digital Caliper 12"
♦ Range: 0-12 in / 300 mm ♦ Resolution: .0005 in / .01 mm ♦ Inch/metric conversion ♦ Preset includes offset for inside jaws ♦ Hold feature ♦ Full size .0005-in digital display ♦ 3.5" Jaw depth allows for measurement of 6" dia. cylinders ♦ Comes with case and extra battery ♦ Available with NIST Traceable Certificate when requested
Cylinder Wrap
Used to minimize fragment scattering and reduce cleanup time after the compression test. Made of canvas/nylon with Velcro fastening strips.
Available Sizes: 6" diameter (W6) 4" diameter (W4)
Cylinder Transport Rack
6 x 12 transport holds 9
4 x 8 transport holds 16
Light weight- only 7lb
Durable Waterproof
Will not rust or rot
Anchor holes permit rack to be secured to truck bed
Allows for placement of cushioning material ( ie: used compression pads)
Eliminates loose specimens in truck bed
Fits inside Deslauriers' "Econ-O-Cure" curing bag for winter transport
Mulitple units can fit in truck bed- Approx 23 Square x 7" high
Sizes Available: 6 x 12 (TRack6) 4 x 8 (TRack4)
Cylinder Carrier Gripping Type
Employs a hand-grip pincer action to secure cylinders.
TC6LH FOR 6" SPECIMEN TC4LH FOR 4" SPECIMEN
H-2945 Cylinder Carrier for 6"x12" molds
Steel cylinder carrier is plated to resist rust. Used to carry 6" dia. concrete cylinders in field or laboratory.
H-2939 Core Length Measuring Device
For determining concrete core lengths. Device accommodates either 4" or 6" diameter specimens up to 24" long. Allows measurements to be taken at the center of the specimen’s upper end, as well as eight equidistant points along the circumference. Measuring rod has gradations 0.10" (2.5mm) apart. Meets ASTM C174.
